ForumsBasic TrainingOnline Maintenance ManualsThe M715 Zone Vin RegistryVPW's M715 Parts ListGalleriesLinks

Go Back   M715 Zone > General Tech > Open Discussion > Open Discussion Archives

 
 
Thread Tools Display Modes
  #1  
Old December 24th, 2006, 02:22 PM
Archiver Archiver is offline
Moderator

 
Join Date: Nov 2006
Posts: 21
Archiver is a Soldier
Default replacing m715 engine

replacing m715 engineTechnical Forums » Open Discussion Archives » replacing m715 engine
http://m715zone.proboards102.com/index.cgi?board=openarchive&action=display&thread=1162377275

replacing m715 engine
Post by fhozaly on Nov 1, 2006, 5:34am

due to the limited power of the engine i am thinking to replace the engine by 8 cyl. v8 GM engine. so is it possible to fit this type of engine without any major modification and is it will effect on the performance of the car?
please if any one have an idea please help
Re: replacing m715 engine
Post by bigwheelbob on Nov 1, 2006, 7:57am

Um, Sir, Most of us have no car's here. However, the 8cyl GM engine fits nicely into our trucks.
Re: replacing m715 engine
Post by gimpyrobb on Nov 1, 2006, 8:36am

A 350 with the 465 trans behind it is common and painless. Relatively(sp?).
Re: replacing m715 engine
Post by Barrman on Nov 1, 2006, 8:54am

Look in the Modified board for information on swaps like this done in the past 6 months. Wait a few weeks and the online Manuals will be available again. There you can read about this kind of swap done over the last 8 years.

It is cheaper to find a complete 2wd truck engine and transmission. Then put them in the M715 as a unit. Depending on the engine, just motor mounts to make the engine fit, fabing a very simple transmission mount and maybe a little size adjustment for the short shaft to the t-case. I drove my 230/T98 powered truck home from work on a Friday, pulled it out and put in a 396 Big Block/NV4500 and drove the truck to work on Monday. The hardest part of the swap for me was the exhaust system.
Re: replacing m715 engine
Post by BinfordM715 on Nov 1, 2006, 9:58am

One of our members makes a kit that will adapt a Chevy V8 engine to the stock transmission and believe it even comes with motor mounts. It seemed to be a complete kit (meaning everything you need) and, while a bit expensive, was actually quite reasonable compared to similar kits.

Post on the "Wanted" board that you are looking for anyone with a kit like that and I'm sure you'll get a response.

Good luck!

P.S. Where are you from?
Re: replacing m715 engine
Post by robertcowan on Nov 1, 2006, 10:59am

thanks binford for the complement if you need and adapter kit cantact me.
bob
Re: replacing m715 engine
Post by firefightinsam on Nov 1, 2006, 10:54pm

My truck was adapted with a novak kit it left things a little crowded at the firewall. It's only a 305 chevy but doesn't want for power.
Re: replacing m715 engine
Post by sermis on Nov 2, 2006, 11:06am

After repoering my M725 with a 350 to the T98 I would change the trans also to an overdrive to drop the rpm's and increase the gas mileage a bit. 6-7 mpg with stock T98 at $2.00+ per gallon, ouch. Really want to go diesel.
Re: replacing m715 engine
Post by fhozaly on Nov 3, 2006, 11:38pm

thanks for the useful replies
Re: replacing m715 engine
Post by sancho on Nov 6, 2006, 1:33am

Has anyone looked into swapping in a 6.5 Turbodiesel?
Re: replacing m715 engine
Post by fisherman on Nov 6, 2006, 1:43am

Yep, pretty sure that's been done, I think a couple members have those in their trucks.
Re: replacing m715 engine
Post by fhozaly on Nov 6, 2006, 6:19am

dear friends


during my search in the net i found very usefull site which will help. this site will tell how to install some types of engines
m 715
i hope it will be usefully

http://www.novak-adapt.com/knowledge/chevy_buick_swap.htm

fhozaly
Re: replacing m715 engine
Post by Barrman on Nov 6, 2006, 9:38am

4 or 5 post up is one by Sermis. He did the Novak kit on his 725. But, as he pointed out. he is getting mid single digit fuel milage with the stock transmission. I put a 396 Big block and od transmission in and I am getting low double digit milage.

Plus, for the price of the Novak kit, you can get the transmission that was behind your new engine or most of the price of a NV4500. That is a better deal in the long run.
installing a bench seat advice
Post by shelleypeak on Nov 7, 2006, 10:54pm


I stuck the battery under the hood during the re-wiring process of this M-715 with w a 6 cyl ford truck motor. I purchased the truck in Auburn In. recently at the MVPA show for 1200.00. I would like to put in a bench seat and am looking for a posting I saw recently on this topic. The guy even had pictures which I would like to review. Please advise if I can still access this posting or if you have advice for me.

I am selling everyting else that I own with 4 wheels . This is one tough vehicle.
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
M37 engine in an M715? chicklin Modified Tech 15 December 30th, 2009 12:02 AM
Replacing NP200 seals chicklin Stock Tech 7 February 14th, 2009 08:49 AM
Need help with replacing motor FireChief Open Discussion 14 January 24th, 2007 04:09 PM


All times are GMT -7. The time now is 04:43 PM.

 

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
1998 - 2018


This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c
If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com

Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC.

Written permission can only be obtained by contacting
brute4c@m715zone.com

Copyright 1998-2018