Results 1 to 8 of 8

Thread: Turbo 350 question???

  1. #1

    Default

    I have a T350 in my 715, and it likes to puke ATF out through the dipstick tube. It doesn't need to be hot necessarily, the other day, it did it 10 minutes after I started the truck. I have a big aluminum cooler on the trans, and it never seems to get hot. Any ideas???

  2. #2

    Default

    Not to be a jerk- but you are filling it with the motor running and in neutral, right? If you overfill them then they'll do that as they heat up.

    I had a turbo 350 in my rig for a while....then the case split and it really puke the fluid.

  3. #3

    Default

    I believe so, I haven't filled it in a long time, my brother added some a couple months ago, said it was way low and thought the vacuum modulator was bad. ie, sucking it into the engine and burning it. I have never had that experience with it. I will check the level again, its probably due for a change anyway, it was a junkyard trans when I put it in. One of those deals, it was rebuilt for a car 10 years ago, and only ran a couple times. Should be fine!1!1!

  4. #4
    Join Date
    Jan 2004
    Location
    NorthEast Texas
    Posts
    261

    Default

    Only two things come to mind 1-loose convertor generating way too much heat . 2-G.M. had a problem with autos puking fluid out several years ago and redid dipstick and tube to a style where dipstick has a seal on cap end that swells and seals tube when lever is flipped down. ask for one for a 86 c-10 (1/2 ton pu.) with a mv4 tranny and you will see what I mean. be sure to get trans to tube seal as well as I think they are revamped too.

  5. #5

    Default Custom plate for the b-ster!!

    How do you know that it is not getting hot? Do you have a gauge on it? I never realized how hot transmissions can get before I installed a gauge on my turbo 350 in my jeep. It would really surprise you

  6. #6
    Join Date
    Dec 2003
    Location
    parsons Kansas
    Posts
    476

    Default

    did you check thevent on top of the transthere is a tube sticking out on the top, upper half of the case, this will also cause fluid belching out the tube and you should have something moving air across the tranny cooler to help cool it too.
    67 M725, 67 M715, 68 M715

  7. #7

    Default

    The cooler is mounted in front of the radiator, with the electric fan pulling through it. I hadn't thought about the vent, that could be plugged with any number of things.

    The dipstick that is in it is an aftermarket chrome one, with a rubber seal at the top, no flip lever though.

    No gauge, but when it started doing it the other day, the truck had only run 10-15 minutes, hi idle in park. Would it build heat that quick like that?

  8. #8
    Join Date
    Dec 2003
    Location
    parsons Kansas
    Posts
    476

    Default

    usually its one of three things. Lack of cooling, plugged up vent tube and or no flow to trans cooler or to small of a cooler can also do it since you arent running it thru the radiator ( I take it). an extra large cooler may be required too. hopefully one of use can give you the info needed to get you taken care of.
    good luck
    dave
    67 M725, 67 M715, 68 M715

Similar Threads

  1. 6.5 turbo
    By foodstamp in forum Open Discussion
    Replies: 21
    Last Post: April 4th, 2011, 01:12 AM
  2. elohim1 : Divorced tranny to Turbo 400 drive shaft question
    By Elohim1 in forum PseudoZone - Open Archive
    Replies: 20
    Last Post: November 11th, 2009, 03:51 AM
  3. chevy 350 and turbo 400
    By ken ruhland in forum Modified Tech
    Replies: 6
    Last Post: November 16th, 2008, 06:38 PM
  4. chevy 6.2L with 350 turbo
    By solekaukini in forum Modified Tech
    Replies: 11
    Last Post: April 25th, 2008, 11:16 PM
  5. 350 / 400 turbo swap
    By Nuke_wanger in forum Modified Tech Archives
    Replies: 3
    Last Post: April 12th, 2004, 07:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Site Upgrade, Design Modifications & Administrative Support by:
Palm River Enterprises LLC, IT Solutions
President: Tom King, User ID=teking
This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c


If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com
Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com

Copyright 1998-2022