Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: elohim1 : Radiator in the bed ??

  1. #11
    Join Date
    Dec 2003
    Location
    Giddings, Texas
    Posts
    7,640

    Default barrman :

    Re: Radiator in the bed ??
    Post by barrman on Nov 2, 2006, 9:59am

    Here is the best picture I have of the fan here at work. It was taken over a year ago, but you get the idea.


  2. #12
    Join Date
    Dec 2003
    Location
    Giddings, Texas
    Posts
    7,640

    Default barrman :

    Re: Radiator in the bed ??
    Post by barrman on Nov 2, 2006, 10:00am

    I still have enough room in front of the fan to use a short socket and a 3/8" ratchet drive to install the bolts.

  3. #13
    Join Date
    Dec 2006
    Location
    Oxford, Ohio 45056
    Posts
    175

    Default elohim1 :

    Re: Radiator in the bed ??
    Post by elohim1 on Nov 2, 2006, 6:52pm


    Quote:
    I've got a 454 and a tilt front- I fit a stock Ron Davis dual pass rad. with two puller fans- fabbed a custom mount. Pass. fan motor misses alt. by about 1/4 inch. Works great though. Gimme your e-mail and I'll sent pix if it helps. Won't be till next week though, I'm headed to Mex this weekend


    Yes, please send pics of this tilt setup to : elohimfirst@msn.com

    Thanks
    Chris

    Good info. gents.

  4. #14
    Join Date
    May 2004
    Location
    Anchorage, Alaska
    Posts
    250

    Default 40grit :

    Re: Radiator in the bed ??
    Post by 40grit on Nov 2, 2006, 8:27pm

    sorry boss, got so friggen busy with DieHard4 filming today...I'm going in tomorrow to work on 715, i'll get them tomorrow...

  5. #15
    Join Date
    May 2004
    Location
    Anchorage, Alaska
    Posts
    250

    Default 40grit :

    Re: Radiator in the bed ??
    Post by 40grit on Nov 3, 2006, 4:53pm

    ok, here's a bunch...

    front view, ground level
    [img=http://img292.imageshack.us/img292/5607/coresupport002qc6.th.jpg]

    top view
    [img=http://img126.imageshack.us/img126/7586/coresupport003ty0.th.jpg]

    passenger side rear view
    [img=http://img293.imageshack.us/img293/4955/coresupport004ht4.th.jpg]

    driver side rear view
    [img=http://img527.imageshack.us/img527/4599/coresupport005aw2.th.jpg]

    yet another view
    [img=http://img170.imageshack.us/img170/7326/coresupport006el6.th.jpg]

    radiator I'm using, with Flexilite 292 monster fans ( 31x19 universal Gm rad)
    [img=http://img527.imageshack.us/img527/2104/coresupportsc1.th.jpg]

    no put together pics, but the rad fits in front, about 3" further forward than stock with the fans behind it...leaves about 1" to front of water pump serp pulley...still has room for auto tranny cooler in front if I decided to change down the road...

    supports are made of steel framing member, cost $11 for 10' section, cut a few pieces out, bent some in half lengthwise and used them for front supports, with a thin strip of rubber, it fits perfect around tanks on radiator, just need to fab top and bottom brackets, and drill holes for fans to mount...

  6. #16
    Join Date
    Dec 2006
    Location
    Oxford, Ohio 45056
    Posts
    175

    Default elohim1 :

    Re: Radiator in the bed ??
    Post by elohim1 on Nov 3, 2006, 9:29pm

    Much appreciated 40grit !!!

Similar Threads

  1. elohim1 : On board air with GM compressor ??
    By Elohim1 in forum PseudoZone - Mod Tech Archive
    Replies: 13
    Last Post: December 15th, 2009, 09:24 PM
  2. elohim1 : BBC header selection, what did you use?
    By Elohim1 in forum PseudoZone - Mod Tech Archive
    Replies: 30
    Last Post: December 15th, 2009, 08:48 PM
  3. elohim1 : Serpentine system and ON board Air ??
    By Elohim1 in forum PseudoZone - Open Archive
    Replies: 3
    Last Post: November 12th, 2009, 03:29 AM
  4. elohim1 : What is the spacing on the points for a 230?
    By Elohim1 in forum PseudoZone - Open Archive
    Replies: 4
    Last Post: November 11th, 2009, 06:09 AM
  5. elohim1 : Which 502 motor should I use?
    By Elohim1 in forum PseudoZone - Open Archive
    Replies: 11
    Last Post: November 11th, 2009, 05:46 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Site Upgrade, Design Modifications & Administrative Support by:
Palm River Enterprises LLC, IT Solutions
President: Tom King, User ID=teking
This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c


If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com
Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com

Copyright 1998-2022