Results 1 to 5 of 5

Thread: lbuck78 : Fording kit cable location

  1. #1

    Default lbuck78 : Fording kit cable location

    Fording kit cable location
    Post by lbuck78 on May 1, 2006, 6:23pm

    Does anyone Know where the fording plate and cable go on the dash? and if so do you have any pictures? I finally got the motor started and I'm just waiting for the tub to come back so I thought I would work on the dash until then. I'm loosing my shop so I have until the 31st to get it done and ready for the street.

  2. #2

    Default socal715 :

    Re: Fording kit cable location
    Post by socal715 on May 1, 2006, 6:35pm

    33-B9. Valve Control Cables and Dual Valve Control
    Using the instruction plate as a template, place it on the instrument panel in location shown in Fig. 33-B7. Locate the center of the large hole 2? in from the left edge of the instrument panel and 4 3/8" up from the lower edge. Center mark the five holes to be drilled. Remove plate and drill four .116? dia. (No. 32 drill) and one 11/16" dia. holes. Then position plate on instrument panel and secure with four (4) 6-18x3/8? self tapping screws.
    Position rubber cable grommet in the existing hole of firewall. Insert dual cables through the instrument panel and install cable control washer and nut over cables. Insert cables through grommet in firewall. Position cable control in instrument panel and secure with washer and nut. Position cable conduits in cable clamp of fording ventilation valve bracket and secure with screw. Position cable wires in valve arms as shown in Fig. 33-B6 making sure cable control knob is all the way in and the arm levers are all the way forward. Tighten arm screw to secure the cable wires.


  3. #3
    Join Date
    Jan 2004
    Location
    Geneva, FL
    Posts
    731
    Blog Entries
    1

    Default teking :

    Re: Fording kit cable location
    Post by teking on May 1, 2006, 6:50pm

    Sweet!!! OK this is a keeper.

  4. #4

    Default lbuck78 :

    Re: Fording kit cable location
    Post by lbuck78 on May 1, 2006, 9:05pm

    ok just one more question, what manual is that picture from? I have a copy of tm 9-2320-244=34p and it just shows the parts breakout

  5. #5

    Default socal715 :

    Re: Fording kit cable location
    Post by socal715 on May 1, 2006, 10:56pm

    TM 9-2320-244-20 Organizational Maintenance Manual ?1999

Similar Threads

  1. lbuck78 : Hard lines for brakes and fuel
    By PseudoZone in forum PseudoZone - Open Archive
    Replies: 2
    Last Post: November 10th, 2009, 11:42 PM
  2. location, location,location...
    By jay r in forum Open Discussion
    Replies: 6
    Last Post: October 14th, 2009, 10:23 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Site Upgrade, Design Modifications & Administrative Support by:
Palm River Enterprises LLC, IT Solutions
President: Tom King, User ID=teking
This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c


If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com
Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com

Copyright 1998-2024