Stock Exhaust Photo Reference

Printable View

May 6th, 2015, 05:35 PM
jeepdan

Stock Exhaust Photo Reference

I have taken a few photos of my stock exhaust to help out future Zoners.
I wish that I would have had this as a reference, it would have saved a lot of time and frustration.
If anyone has any corrections, please comment.

Here is the tailpipe hanger. The rubber insulator is from VPW, and the clamp is something that I made by hand from looking at the parts illustration.
http://i1012.photobucket.com/albums/...psovudjkjb.jpg
http://i1012.photobucket.com/albums/...pssguj45ys.jpg
May 6th, 2015, 05:36 PM
jeepdan

A few more of the various locations.
http://i1012.photobucket.com/albums/...psu4l7xwpv.jpg
http://i1012.photobucket.com/albums/...pseunxrry1.jpg
May 6th, 2015, 05:37 PM
jeepdan

Can't leave out a shot of the engine:D
http://i1012.photobucket.com/albums/...psm3pzppxt.jpg
May 6th, 2015, 07:24 PM
brute4c

Holy cow...that is absolutely beautiful and so very nice of you to post!!!
May 6th, 2015, 08:54 PM
JimmieM725

Dang, Shiney DriveShaft too. I followed your Build its Beautiful.... But Most of All-- THANKS FOR THE KNOWLDGE!!!!! Its been very helpful.;)
May 6th, 2015, 10:33 PM
jeepdan

Thanks:)

I just realized that I didn't show any of the cable hangers at the muffler.
I will post them tomorrow.
May 6th, 2015, 10:36 PM
bmac6026

You have the truck that I have to see in person ! very nice!
May 7th, 2015, 12:46 PM
David Zelinski

I like your hanger set up! I'll post a pix of what we came up with for mine. and also- I have so far to go to have my truck looking like yours! :p
May 11th, 2015, 11:20 AM
Von

Wow... Gorgeous! The red backing plates are a nice touch.

My truck is lucky I hit it with a power washer while I had the engine out... and it's not a very powerful washer.

And knowledge! The hanger bolted to the transmission mount. When I pulled that off on mine I didn't know if that was stock or another goofy field mod...
May 11th, 2015, 01:24 PM
jeepdan

Quote:

Originally Posted by Von

Wow... Gorgeous! The red backing plates are a nice touch.

My truck is lucky I hit it with a power washer while I had the engine out... and it's not a very powerful washer.

And knowledge! The hanger bolted to the transmission mount. When I pulled that off on mine I didn't know if that was stock or another goofy field mod...

Thanks:)
Von,
The backing plates were left red oxide primer as they came from the factory.
My camera makes them appear more red than they actually are.
May 11th, 2015, 07:01 PM
67smith

while the backing plates look like hemi orange! on my PC.

I picked up some red oxide for my deuce, looks almost red orange in person.

very nice truck. maybe someday mine will look 3/4's as good, got a long way to go though, and will be doing some custom stock looking touchs(Stainless exhaust;))
October 28th, 2015, 11:39 PM
txleadfoot

Exhaust Hangers

Dan, would love to see photos including the hangers!

Quote:

Originally Posted by jeepdan

Thanks:)

I just realized that I didn't show any of the cable hangers at the muffler.
I will post them tomorrow.
October 29th, 2015, 09:14 AM
1953M38A1

Very nice job! I would like to ask where you got or what you are using for the body mounts? yours look brand new. I would like to replace all of mine also.
Thanks Andrew